Clipsal C-Bus Manuale delle Istruzioni Pagina 132
- Pagina / 148
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
C-Bus™ Basic Programming 1250SM0904R10/09
C-Bus™ Products Training Course 10/2009
126 © 2009 Schneider Electric. All Rights Reserved.
When using the Light Level parameter, it is best to disable the sensor from
operating at night to ensure the light does not turn ON automatically due to
low Lux levels. A group address which is programmed into the Enable
Group parameter, will behave as follows:
when the Enable group is ON, the light level sensor will operate
when the Enable group is OFF, the light level sensor will not operate.
NOTE: If there is no Enable group, the light level sensor will always be
enabled by default.
The Indicator parameter allows you to specify which group address the
indicator will show the status of.
The Ambient Light section of the programming GUI will display the reflected
light level that is being read at the light level sensor (not at the floor). This is
used as a guide to determine the target Lux level. To view the reflected light
level you must ensure that:
Toolkit is physically connected to the C-Bus network
The Refresh check box is selected, which will update the Last
Measurement parameter every five seconds.
The Target parameters consist of 2 settings as shown below.
Parameter Description
Target The Target parameter allows you to specify the level that the Light ON/OFF
and Light Level parameters will operate at. Remember that this target is
measured at the unit, not at the floor.
Margin The Margin parameter allows you to specify the amount of light variation
that will occur before the Light Level Sensor will control the load. This is
used to ensure that scenarios such as passing clouds do not have sudden
affect on the loads.
Table 46 - Setting the target level on a light level sensor
The image below shows the relationship between the ambient light level,
the Target and the Margin.
Time
0
700
Light Level (Lux)
Load is ON
or Ramping
UP
No Action Due to
Margin
Load is
OFF or Ramping
Down
Target
&
Margin
Figure 111 - Load control depending on light level
- Basic Programming 1
- Products Training Course 1
- Please Note 3
- Class B FCC Statement 3
- Safety Precautions 4
- Clipsal Introduction 7
- What Is C-Bus? 8
- Why Use C-Bus? 9
- Functionality 10
- Simple Wiring 10
- C-Bus Principles 13
- C-Bus Power Supply 14
- PC Interface 14
- Network Bridges 15
- Input Units 16
- C-Bus Wall Switches 17
- C-Bus Sensors 18
- Miscellaneous Inputs 20
- Output Units 21
- C-Bus Dimmers 23
- Maximum Load Calculations 25
- Fluorescent Dimming 27
- IR Transmitter 28
- Software 29
- C-Bus Cable 30
- Cable Current 31
- Cable Terminations 31
- 1 2 3 4 5 6 7 8 32
- Cable Topologies 33
- C-Bus Units 36
- C-Bus Voltage 37
- Power Supply Placement 38
- 1 km of C-Bus Cable 39
- Over Voltage Protection 40
- C-Bus Current 41
- C-Bus Current Consumption 42
- C-Bus Clock 43
- Network Burdens 44
- Mains Segregation 45
- Learn Mode 47
- Selecting Output Channels 48
- Learn Mode Operations 49
- Timer Configurations 50
- Super Learn Mode 51
- C-Bus Addressing 53
- C-Bus Toolkit 54
- 5500NB 5500NB 5500NB 5500NB 54
- Network Address 56
- Network 254 56
- Network 253 56
- Group Address 001 60
- Group Address 002 60
- Group Address 003 60
- Group Address 004 60
- Group Address 01 61
- C-Bus Tags 62
- How C-Bus Works 63
- L5504D2U 65
- L5504RVF 65
- 5084NL 5082NL 65
- C-Bus Message Types 66
- Status Report Interval 66
- C-Bus Into to Toolkit 67
- C-Bus Toolkit Overview 68
- The C-Gate Console 69
- The Toolkit Main Menu 70
- The Navigation Tree 71
- The Toolbar 73
- Installing USB Drivers 80
- Creating a Project 80
- Editing a Network 82
- Creating Group Addresses 83
- Add Units to Database 84
- Adding Units Manually 85
- Scanning a Network 90
- Readdressing C-Bus Units 92
- Serial Number Readdress 94
- Application Log 96
- Programming C-Bus Units 97
- DIN Rail Relays 98
- Channel 1 101
- Logic Group 101
- Channel 2 101
- Turn On Tab 102
- Recovery Tab 103
- Restrike Delay Tab 104
- Global Tab 105
- Status Tab 106
- DIN Rail Dimmers 107
- Logic Tab 108
- Min/Max Tab 112
- Dual Applications 117
- Indicators 119
- Disable All Keys 121
- Corridor Linking 123
- Timing Parameters 123
- Micro Functions 125
- Passive Infrared Sensors 128
- PIR Function Details 129
- Sensor Enable/Disable 130
- False Triggering Sensors 130
- Light Level Sensors 131
- Remote Triggering Scenes 136
- Variants 141
- Labelling Scenes 142
- C-Bus Diagnostics 143
- Analysis Tools 144
- Multimeter 145
- Oscilloscope 146
- Diagnostic Utility 146
- Diagnostic Utility Setup 147
- Support and Training 148
Prodotti e manuali riguardandi Monitor touchscreen Clipsal C-Bus
Monitor touchscreen Clipsal C-Bus2 Specifiche
(120 pagine)
(120 pagine)
Monitor touchscreen Clipsal C-Bus Guida Utente
(60 pagine)
(60 pagine)
Monitor touchscreen Clipsal C-Bus Manuale Utente
(15 pagine)
(15 pagine)
Monitor touchscreen Clipsal C-Touch Guida Utente
(20 pagine)
(20 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale